Inverto Unicable II programmable 40mm LNB for 32 Participants

The Inverto Unicable II LNB enables installations with up to 32 satellite receivers via a single cable. Alternatively, the LNB can be configured so that 32 freely selectable transponders are available in static mode. The LNB supports the standard EN50494/EN50607 protocols so that the connected receivers can access every transponder of the received satellite (also known as "dynamic" mode).

Features
- 4K UHD DVB-S2 compliant with low phase noise
- Very high cross-polarization isolation
- Programmable configuration
- Legacy emulation mode
- Quiet figure
- energy efficient

Alternatively, the LNB can be configured in such a way that a programmable set of up to 32 transponders (depending on the bandwidth of the desired transponders) is down-converted and stacked over its output (also known as "static" mode). In this mode, an unlimited number of receivers can be connected and access these transponders.

Unicable II LNBs offer an affordable and elegant solution for distributing satellite signals to multiple set-top boxes (multiroom) or multi-tuner PVRs over existing cables, significantly reducing the cost and complexity of installation at home will. The static mode, with which an unlimited number of receivers can be connected to the LNB via a single cable distribution, makes installations in buildings, campuses, and closed communities much cheaper and easier than ever before. The operating mode (dynamic/static), the output power level, the channel bandwidth, the UB frequencies, and the alignment mode of the dish are all programmable and can be configured and updated on-site using Inverto's Satpal* controller.

Technical Info
- Input frequency range: 10.7 GHz ~ 12.75 GHz
- Output frequency range: 950 ~ 2150 MHz
- Noise figure: 1 db max.
- LO frequency: 10.4 GHz
- LO temperature drift: 1 MHz max.
- LO initial accuracy: 500 khz max.
- LO phase noise at 1 kHz: - 60 dBc / Hz max.
- LO phase noise at 10 kHz: - 80 dBc / Hz max.
- Conversion gain: 55 dB min.
- Variation gain (over the entire band): ± 0.75 dB / UB max.
- Image rejection: 40 dB min.
- 1 dB compression point (@ output): 0 dBm min.
- Cross polarization isolation: 23 dB min.
- Output VSWR: 2.5: 1
- Current consumption: 350 mA max. @ 13.5 V.
- Operating temperature: - 30 ° C ~ + 60 ° C.
- Output impedance: 75 O
- Output connector type: F-type (female)
- Weight: 164 g
- Bandwidth User Band: Configurable, 10 MHz ~ 64 MHz (Standard 30 MHz)
- Control protocols: Diseqc1.x / diseqc2.x, en50494 / en50607
- Number of user bands: Up to 32 user bands

Unicable II (dCSS) Port Specifications | Standard configuration (32 UBs in dynamic mode)
- UB1 1210 MHz (EN50494 + EN50607)
- UB2 1420 MHz (EN50494 + EN50607)
- UB3 1680 MHz (EN50494 + EN50607)
- UB4 2040 MHz (EN50494 + EN50607)
- UB5 984 MHz (EN50494 + EN50607)
- UB6 1020 MHz (EN50494 + EN50607)
- UB7 1056 MHz (EN50494 + EN50607)
- UB8 1092 MHz (EN50494 + EN50607)
- Ub9 1128 MHz (en50607)
- Ub10 1164 MHz (en50607)
- Ub11 1256 MHz (en50607)
- Ub12 1292 MHz (en50607)
- Ub13 1328 MHz (en50607)
- Ub14 1364 MHz (en50607)
- Ub15 1458 MHz (en50607)
- Ub16 1494 MHz (en50607)
- Ub17 1530 MHz (en50607)
- Ub18 1566 MHz (en50607)
- Ub19 1602 MHz (en50607)
- Ub20 1638 MHz (en50607)
- Ub21 1716 MHz (en50607)
- Ub22 1752 MHz (en50607)
- Ub23 1788 MHz (en50607)
- Ub24 1824 MHz (en50607)
- Ub25 1860 MHz (en50607)
- Ub26 1896 MHz (en50607)
- Ub27 1932 MHz (en50607)
- Ub28 1968 MHz (en50607)
- Ub29 2004 MHz (en50607)
- Ub30 2076 MHz (en50607)
- Ub31 2112 MHz (en50607)
- Ub32 2148 MHz (en50607)

Delivery
1x Inverto Unicable II programmable dCSS 40mm LNB for 32 participants (IDLU-32UL42-UNBOO-OPP)

* SatPal controller not included, available separately as an accessory.